Data Sheet

Product Code:



3.5" LCD, 480x320, Support CVI, TVI, AHD, Micro SD Card Slot, BNC 1in/1out, RS232, RS485, Audio, UTP test, 3000Ah Battery, DC5V input/ DC12V output

  • Video signal testing
    built-in LCD-TFT RGB)x320P full-view display screen easily displays camera image quality. LCD screen brightness/Contrast/Color Saturation adjustable. Suitable for field construction and maintenance work
  • Video signal level test
    Test video signal strength attenuation, longer video signal cable will cause the image to be dim, and reduce the image dynamic range, video signal is too strong, it will cause the virtual shadow, and reduce the sharpness of the image. It also can display the video level value, if out of range, notices will be display in the screen.
  • PTZ controller
    Display the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the controlling parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set and call preset position.
  • Color bar generator
    Video Generating, the PAL/NTSC multi-system color bar video generator (Eight-system switchable,transmit/receive eight-system colorful imagines). By receiving the video color bar to test the video channel whether transmit normally. And judge whether the color is different, because of the transmission loss or interference, it suitable for Video transmission of the field tests, such as optical video transmitter and receiver, video cable etc. The new function color bar can test the image whether shift.The color bar (red, green, blue, white, black) test the monitor whether have white or black dot etc.
  • DC12V 1A output power
    Power the camera with DC12V (1A) power output from the tester. It is helpful for demo and testing when the power supply is not available.
  • Audio test
    Test the audio input from pickup devices. Connect the tester and pickup device with the audio cable.
  • Cable tester
    Test LAN cable or telephone cable. Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting status, cable type and the sequence of wires will be displayed, as well as the serial number of the cable tester kit.
  • Search PTZ protocol code
    Search the Control protocol code from Multifunction keyboard or DVR by RS485 /RS232 interface, test the PTZ control command data whether received anomaly and RS485/RS232 data transmission. Screen displays 16 hexadecimal codes such as PELCO-P:A0 00(Add) xx xxxxxx AF xx PELCO-D:FF 01(Add)xx xxxxxxxx
  • PTZ address scan
    Search up the ID of PTZ camera. Help the engineer search the speed dome address quickly.
  • Image digital zoom
    Set image 10x zoom, can view and display the details by 1x,2x,3x,4x,5x,6x - 10X zoom in the monitor and tester.
  • Video snapshot Capture the video image and save the current video frames as JPEG file
  • Video recording Record and save the current video in the SD card
  • Video playback Video image and record files are saved in the SD card. Storage file directory can be created according to the date
  • Port flicker
    The tester will send special signals to make the connected POE port flicker at special frequency, which will enable the installers to easily and quickly find the connected ethernet cable. This function can prevent mistakenly insertion or disconnection non-corresponding cable to artificially interrupt network connection.
  • IP address scan
    In digital IP surveillance applications, if IP cameras IP address is not clear or forgotten; the device cannot be used. IP address scan can quickly search the connected IP camera or other network devices IP address.
  • Link monitor
    To add an IP camera or other network device to the current network group, the new IP address must not be occupied, otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor can check if the new setting IP address is occupied.
  • PING test
    PING is the most conventional network debugging tools; It is used for testing if the connected IP camera or other network equipments ethernet port is working normally and the IP address is correct.
  • POE tester / POE voltage measurement
    It can test the POE voltage when the POE switch is supplying the POE power to IP camera. It can clearly display the power+ and power- on the ethernet cable pins, each cable pins voltage and the failure connection of cable pin series numbers.
  • LED lamp
    It is useful for the Engineer to install and maintain security system at night through switching LED On/Off pressing button.
  • F1/F2 User-defined shortcut keys
    The user-defined shortcut key is designed for improving the efficiency for the engineer, anytime press, easy to operate.
  • TDR Break-point and short-circuit measurement (optional function refer to the last page)
    New function: TDR cable testing, accurately measure BNC cable, network cable, control cable break-point and short-circuits location. It improves working efficiency.
  • Optical Power Meter
    The New tester adopts the most advanced handheld instrument specific integrated chip , achieve ultra-low power operation, with the 3.5 TFT-LCD High-definition screen display ,five wavelength calibration points 1625nm,1550nm , 1490nm , 1310nm , 1300nm , 850nm.Linear or nonlinear optical power display, it can measure the optical power value, and also be used for Relative measurement of optical fiber link loss. It is necessary tool for fibre-optic communication, cable television system and security system maintenance.
Product Name CCTV Tester AHD/ CVI/ TVI
LCD Screen & Physical
Screen Size 3.5 inch
Resolution 480*320
Touch screen N/A
Micro SD Card Support
Battery 3.7V DC 3000mAh
HDMI output N/A
Power input DC 5V 1.5A
Working time 8 hours working
Analog Signal Test
Analog video input Support, PAL / NTSC
Input connector BNC, 1CH input / 1CH output
Color bar generator Support
Digital zoom (1-10X ? Support analog image zoom
Analog video record Support
Analog video playback Support
PTZ control RS232 / RS485
Audio test 1CH input
UTP cable test Support

DC 12V Power output

Support, max. current 1A
Remark Only 1 function available out of optical power meter & visual fault locator.

Write a review

Please login or register to review